smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     NETLIST SSD 8GB-001
Serial Number:    --
Firmware Version: S5FAM017
User Capacity:    8,012,390,400 bytes [8.01 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      < 1.8 inches
TRIM Command:     Available
Device is:        Not in smartctl database 7.3/5319
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Fri Oct  7 12:28:55 2022 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  255) seconds.
Offline data collection
capabilities: 			 (0x1b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					No Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   2) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     PO-R--   100   100   050    -    232
  9 Power_On_Hours          -O--C-   100   100   000    -    20000
 12 Power_Cycle_Count       -O--C-   100   100   000    -    212
168 Unknown_Attribute       -O--C-   100   100   000    -    11
176 Erase_Fail_Count_Chip   PO----   100   100   010    -    14
177 Wear_Leveling_Count     -O--C-   100   100   010    -    10160
192 Power-Off_Retract_Count -O--C-   100   100   000    -    113
170 Unknown_Attribute       PO----   100   100   010    -    8
173 Unknown_Attribute       -O--C-   100   100   000    -    10358
218 Unknown_Attribute       PO-R--   100   100   050    -    8
231 Unknown_SSD_Attribute   PO-R--   100   100   000    -    0
233 Media_Wearout_Indicator PO-R--   100   100   000    -    49261
241 Total_LBAs_Written      PO--C-   100   100   000    -    29863
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O     51  Comprehensive SMART error log
0x03       GPL     R/O     64  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 58
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 58 [57] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 e0 00 00 00 00 00 48 40 00  Error: UNC 224 sectors at LBA = 0x00000048 = 72

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:03.612  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:03.112  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.862  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.362  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.112  READ DMA

Error 57 [56] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 e0 00 00 00 00 00 48 40 00  Error: UNC 224 sectors at LBA = 0x00000048 = 72

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:03.112  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.862  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.362  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.112  READ DMA
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.862  READ LOG EXT

Error 56 [55] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 e0 00 00 00 00 00 48 40 00  Error: UNC 224 sectors at LBA = 0x00000048 = 72

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.862  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.362  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.112  READ DMA
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.862  READ LOG EXT
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.362  READ LOG EXT

Error 55 [54] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 e0 00 00 00 00 00 48 40 00  Error: UNC 224 sectors at LBA = 0x00000048 = 72

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.362  READ DMA
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.112  READ DMA
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.862  READ LOG EXT
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.362  READ LOG EXT
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.112  READ LOG EXT

Error 54 [53] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 e0 00 00 00 00 00 48 40 00  Error: UNC 224 sectors at LBA = 0x00000048 = 72

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 e0 00 00 00 00 00 48 40 00 26d+07:16:02.112  READ DMA
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.862  READ LOG EXT
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.362  READ LOG EXT
  2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+07:16:01.112  READ LOG EXT
  ef 00 02 00 00 00 00 00 00 00 00 40 00 26d+07:16:01.112  SET FEATURES [Enable write cache]

Error 53 [52] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 ee c7 08 e0 00  Error: UNC 8 sectors at LBA = 0x00eec708 = 15648520

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:43.362  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:38.362  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:33.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:28.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:23.112  READ DMA EXT

Error 52 [51] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 ee c7 08 e0 00  Error: UNC 8 sectors at LBA = 0x00eec708 = 15648520

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:38.362  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:33.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:28.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:23.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:18.112  READ DMA EXT

Error 51 [50] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 ee c7 08 e0 00  Error: UNC 8 sectors at LBA = 0x00eec708 = 15648520

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:33.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 08 e0 00 26d+07:14:28.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:23.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:18.112  READ DMA EXT
  25 00 00 00 08 00 00 00 ee c7 00 e0 00 26d+07:14:13.112  READ DMA EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            8  Command failed due to ICRC error
0x0003  2            8  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  4           59  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4           80  Device-to-host register FISes sent due to a COMRESET
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC



